Ascend Pipeline Configuration for KCnet
NAT (Network Address Translation) Screens:
Main Edit Menu...
Configure...
Switch Type=NI-1 (or as obtained from your ISDN
provider)
Chan Usage=Switch/Switch
My Num A=(put in your 1st local 7 digit phone number)
My Num B=(put in your 2nd local 7 digit phone number if 128k, leave
blank if 64k)
SPID 1=(your 1st SPID number assigned to you by your ISDN provider,
generally the 9 digit area code and phone number followed by 0101)
SPID 2=(your 2nd SPID number assigned to you by your ISDN provider if
128k, leave blank if 64k, generally the 9 digit area code and phone
number followed by 0101)
Ans Voice Call=No
My Name= (the user id provided by KCnet)
My Addr=(enter any reserved, vaild IP address such as
192.168.100.100/24)
Rem Name=KCnet
Rem Addr=(100.100.100.100/24)
Dial #=(phone number assigned by KCnet)
Route=IP
Bridge=No
Send Auth=PAP
Send PW=*****
Recv Auth=None
Recv PW=N/A
Save=(go ahead and save your changes)
Main Edit Menu...
Ethernet...
Static Rtes...
Default...
Name=Default
Active=Yes
Dest=0.0.0.0/0
Gateway=0.0.0.0/0
Metric=1
Preference=100
Private=Yes
Main Edit Menu...
Ethernet...
Mod Config...
NAT...
Routing=Yes
Profile=KCnet
FR address=0.0.0.0
Lan=Single IP addr
Static Mappings...
Def Server=(leave at default setting)
Reuse last addr=(leave at default setting)
Reuse addr timeout=(leave at default setting)
Main Edit Menu...
Ethernet...
Mod Config...
Ether options...
IP Adrs=192.168.100.100
2nd Adrs=(leave at default setting)
RIP=Off
RIP2 Use Multicast=(leave at default setting)
Ignore Def Rt=(leave at default setting)
Proxy Mode=Off
Filter=(leave at default setting)
IPX Frame=(leave at default setting)
IPX Enet#=(leave at default setting)
IPX Pool#=(leave at default setting)
IPX SAP Filter=(leave at default setting)
IPX SAP Proxy=(leave at default setting)
IPX SAP Proxy Net#1=(leave at default setting)
IPX SAP Proxy Net#2=(leave at default setting)
IPX SAP Proxy Net#3=(leave at default setting)
Handle IPX Type20=(leave at default setting)
Routing a subnet of addresses to your
network:
Main Edit Menu...
Configure...
Switch Type=NI-1 (or as obtained from your ISDN
provider)
Chan Usage=Switch/Switch
My Num A=(put in your 1st local 7 digit phone number)
My Num B=(put in your 2nd local 7 digit phone number if 128k, leave
blank if 64k)
SPID 1=(your 1st SPID number assigned to you by your ISDN provider,
generally the 9 digit area code and phone number followed by 0101)
SPID 2=(your 2nd SPID number assigned to you by your ISDN provider if
128k, leave blank if 64k, generally the 9 digit area code and phone
number followed by 0101)
Ans Voice Call=No
My Name= (the user id provided by KCnet)
My Addr=(a valid address in the subnet assigned by KCnet,
xxx.xxx.xxx.xxx/27)
Rem Name=KCnet
Rem Addr=(ip address of the KCnet access server, xxx.xxx.xxx.xxx/24,
provided by KCnet)
Dial #=(phone number assigned by KCnet)
Route=IP
Bridge=No
Send Auth=PAP
Send PW=*****
Recv Auth=None
Recv PW=N/A
Save=(go ahead and save your changes)
Main Edit Menu...
Ethernet...
Connections...
KCnet...
Ip options...
LAN Adrs=(same as remote address, xxx.xxx.xxx.xxx/24)
WAN Alias=0.0.0.0
IF Adrs=(static ip address assigned by KCnet, xxx.xxx.xxx.xxx/24)
Preference=60
Metric=1
DownPreference=120
DownMetric=7
Private=No
RIP=Off
Client Pri DNS=0.0.0.0
Client Sec DNS=0.0.0.0
Client Assign DNS=No
Client Gateway=0.0.0.0
DNS settings if desired, not necessary
Main Edit Menu...
Ethernet...
Mod Config...
DNS...
Domain Name=kcnet.com
Sec Domain Name=
Pri DNS=209.240.96.6
Sec DNS=209.240.96.11
Allow As Client DNS=Yes
List Attempt=No
List Size=N/A
Client Pri DNS=0.0.0.0
Client Sec DNS=0.0.0.0
Enable Local DNS Table=No
Loc.DNS Tab Auto Update=No
The following screen is only needed for dedicated
connections:
Main Edit Menu...
Ethernet...
Connections...
KCnet...
Telco options...
AnsOrig=N/A
Callback=N/A
Exp Callback=N/A
Call Type=(set to to Perm/Switched for dedicated connection, leave at
default of Switched for dial on demand)
Group=N/A
FT1 Caller=N/A
Data Svc=56K
Force 56=N/A
Bill #=
The following screen is only needed if forcing to 128k:
Main Edit Menu...
Ethernet...
Connections...
KCnet...
Telco options...
Encaps options...
Send Auth=PAP
Send PW=*SECURE*
Aux Send PW=N/A
Recv PW=N/A
DBA Monitor=Transmit-Recv
Base Ch Count=(set Base Ch Count=2 for 128k, set to 1 for 64k)
Min Ch Count=1
Max Ch Count=2
MRU=1524
LQM=No
LQM Min=600
LQM Max=600
Link Comp=Stac
VJ Comp=Yes
Dyn Alg=Quadratic
Sec History=15
Add Pers=5
Sub Pers=10
Target Util=70
Idle Pct=0
Setting Telnet Password
1.Open the Ethernet > Mod Config > Ether Options.
2.Enter a Telnet password up to 20 characters long.
For example:
Telnet PW=telnet-pwd
3.Close the Ethernet profile.
For more information on Ascend security considerations
see http://www.ascend.com/security/security.html.
Return
to Support Page
|
